Overflow Pipe White Drain Glue
[P464]

Gene 404 is a polyvinyl chloride (PVC) solvent cement used for joining PVC pipe and socket-type fittings which meet Class 12454B as defined in ASTM Specification D 1784, and for joining ABS to PVC transition pipe and socket-type fittings.

Gene 404 is a clear, regular body cement.

CHARACTERISTICS:

NSF approved for potable water	Exceeds ASTM D 3138 specifications
UPC (IAPMO) listed under File No. 1796	Manufactured with only high quality 100% virgin materials
Exceeds ASTM D 2564 specifications	Faster setting regular body formula is ideal where makeup time is at a premium on smaller diameter pipe

APPLICATIONS:

Gene™ 404 is specifically formulated for all PVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers, and drain, waste and vent (DWV).

It is for use on PVC pipe through 2" Schedule 40 pressure piping and up to and including 4" Schedule 40 non-pressure (DWV) piping.

It may also be used for making up transition joints between ABS and PVC in non-pressure (DWV) piping.

INSTRUCTIONS:

1. Store and apply between 40 degree F and 120 degree F. Protect from freezing. Do not use if cement has become curdled, lumpy, thickened or is beyond two years from date stamped on container. Do not thin.
2. Cut pipe end square and remove ragged edges and burrs. Clean fitting socket and pipe of dirt, grease, and moisture, and check for proper fit. Apply PRIMER to all PVC surfaces in accordance with instructions. For transition joints, ABS surfaces do not have to be primed. While still wet, quickly begin solvent cement application.
3. Wear non-permeable gloves during application to avoid skin contact.
4. Shake well before using and stir frequently while using. Apply with supplied dauber applicator. For pipe greater than 2" diameter, use natural bristle brush sized to 1/2 pipe diameter.
5. Apply thin coat evenly to socket. Quickly apply heavy coat to pipe end. Cement must remain wet. If not, recoat. Then quickly insert pipe into fitting with slight twisting movement until it bottoms out.
6. Hold pipe into fitting for at least 30 seconds to prevent pipe from backing out of tapered socket.
7. Wipe excess cement from joint with rag. Allow 15 minutes before handling. Avoid full-line pressure for 24 hours. Cure time varies with size, fit, temperature and humidity.

PRECAUTIONS:

D A N G E R!

VAPORS EXTREMELY FLAMMABLE
VAPORS ARE HEAVIER THAN AIR AND CAN COLLECT IN LOW AREAS

VAPORS MAY CAUSE FLASH FIRE

CONTAINS: Tetrahydrofuran, Methyl Ethyl Ketone, and Cyclohexanone. PRECAUTIONS: Vapors extremely flammable. Harmful if swallowed or inhaled. Causes eye and skin irritation. Keep away from heat, sparks, and flames until vapors are gone. Use only with good cross-ventilation. Wear adequate protective gear and clothing. Avoid breathing vapors and contact with skin, eyes and clothing. Wash after handling. FIRST AID: For any overexposure, get immediate medical attention after first aid is given. Eyes - Flush 15 minutes with clean water. Skin - Wash with soap and water. Inhalation - Remove to fresh air. Ingestion - DO NOT INDUCE VOMITING. Only if conscious, give large amounts of water. FIRE AND SPILLS: For fire, use water fog, CO2, foam, or dry chemicals. Clean up spills immediately with inert absorbents. STORAGE AND HANDLING: Store in cool, well-ventilated area. Keep container upright and tightly closed. Do not reuse empty container. KEEP OUT OF REACH OF CHILDREN.

For additional information, refer to Material Safety Data Sheet.

SPECIFICATIONS:

Wt/Gal @ 77 degree F	7.8 +- .2 lbs/gal.
Flash Point SETA CC	28 degree F
Color	Clear
Shelf Life	2 years

Suggestions and recommendations covering the use of our products are based on our past experience and laboratory findings. However, as we have no control as to the methods and conditions of application, we only assume responsibility for the uniformity of our products within manufacturing tolerances.

LIMITED WARRANTY:

RectorSeal® makes the Limited Express Warranty that when the instructions for storage and handling of our products are followed we warrant our products to be free from defects. THIS LIMITED EXPRESS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND OF ANY OTHER OBLIGATION ON THE PART OF RECTORSEAL®. The sole remedy for breach of the Limited Express Warranty shall be the refund of the purchase price. All other liability is negated and disclaimed, and RectorSeal® shall not be liable for incidental or consequential damages.

MANUFACTURED IN U.S.A. BY

RectorSeal®